Here's some tips how to maintenance
DTG printer. Actually, maintaining the
DTG Printer Not as long as it would require special expertise in performing routine maintenance and then the printer will be maintained.
1. Try to always familiarize to do head cleaning when starting up the DTG Printer. With regular cleaning can make printer dumping dirt in advance of dirt that settles at the end of the head. so that the next print will produce better color.
2. Shut down and rest your printer usage every 3/4 hour for 10 minutes. Do not get used printer is powered on continuously because it would cause pf / cr heat engine which will make motherboard and head come hot and make damage. Get used to rest the printer within a certain time. let the printer temperature is cooling down so that it is always excellent.
3. Always check the printer disposal if it wants full and empty the waste immediately. If in full condition so can lead evaporate dumping dirt into the capping station and then up again to the head.
4. Clean the capping station. Capping station is the most important to clean it every day, because there is always a sediment capping station which resulted disposal is not perfect and can lead to supply ink from the cartridge to the head is not perfect until the printout is generated will be less good.
5. Clean the wiper. Wiper also components that must be cleaned every day after using. Former ink will often settle on the wipers and become crusty, this can lead to head scratched and covered in ink crust. One of the causes that can make faulty printer. Get used to cleaning up to the tip end of the wiper and clean of dirt. Do not let a single day of your wiper dirty because it will be crusty.
6. Install the stabilizer. Often we are not aware of tension in the room we are stable or not. if you checked the stability we can buy adapters to check the voltage. if not stable, then immediately post stabilizer. Unstable voltage can create an electrical short which could cause shorting on the printer. Shorting the printer can be spread anywhere where even though it came from only one source. So before it happens check is electrical voltage to your room in advance.
7. Remove contact. If the printer is turned off do revocation electrical outlet that really stops flowing to the printer. In addition to stopping the flow of voltage in order to avoid revocation of contacts also serves the printer to complete rest for not doing any work sehingg when the printer is turned back in tip top condition.
That's what can I say about the DTG printer treatments may be beneficial
DTG printers Blinking Simultaneously
If there is an event like this then try some of the following tips:
1. Check sensor motor on the right side printer
Try to clean the sensor nodes and the check disc flexi cable, turn the printer off and restart the printer.
2. Check PF motors, the location right beside the printer
Often use can make PF motor becomes hot and weak, It can also cause blinking simultaneously. PF try to replace with a new motor.
3. Check the sensor under the tray
Sensors under tray often shake and do not even touch the rail this can cause a blinking simultaneously anyway because there is no sensor that touches the rail. Try to set back a distance sensor to rail tray. turn off and restart the engine of your DTG.
4. Error Mainboard
If all is your check now try to check the motherboard. There are some things that cause the motherboard error. It could be due to a short circuit shorting if one of the flexi cable can also be exposed to liquid or drop out fuse on the motherboard. If the shorting happens then you should replace with a new motherboard, if the fuse / blown fuse fuse buy enough for your motherboard and plug using solder, for the tutorial will be conveyed to the upcoming discussion.
5. Head Weak
Air DTG printer engine to print basic printer paper where if we read the manual booknya have the ability to print continuous quantity. eg on epson 1390 is capable of printing up to 500 sheets of paper per month, if they continue to be forced to work there will be a general error due to a weak head. if it happens like this then your head must be replaced with new ones. If you do not want this to happen, prevention is to rest the printer every 5 shirt for approximately 10 minutes. after working 5 shirts try to turn off for 10 minutes before continuing the work.
6. Replace 1 unit
If the above is not detected and you do not know what's wrong with the machine DTG you, buy one unit of a new printer and have the vendor machine DTG you to replace with a new unit using the same framework, only the unit of the printer not to order a new one ,
there DTG printer engines for screen printing are usually dark colored shirt we have to use white ink as a base before color CMYK process. Hals will make the results of screen printing on dark colored shirt became look good. But what happens if white ink that comes out is not the maximum. It could be your head stuck and will affect results to a color less bright
Head Dead End
We are often confronted by the problem of clogged heads that make white ink does not come out with good results and therefore contributes to the brightness of a dark T-shirt screen printing. Why could happen so? This could have happened if the maintenance is not good and not routine. As we know that the white ink on DTG printers are often quickly dries and settles. therefore often do routine maintenance on the head so that the results of the resulting color is always bright without any problems.
Catridge and Hoses
In addition to the head might be possible precipitates in the cartridge and your hose. Try to also check the condition of the cartridge once a month and hoses. if there are deposits try to clean using injection and liquid cleaning solution. If difficult to be cleaned buy a new cartridge on the market include the hose and tube. Notice to purchase a package that is equipped with a reset button on the cartridge. So that if an error occurs later in the cartridge you can immediately reset the cartridge without having to remove the cartridge and do a reset using a special tool resetter.
DTG ink White
Which often create problems in white ink printer ink white DTG. Why could happen so? Because of white ink DTG highly concentrated even 2 times more concentrated than the usual CMYK inks and dry process that is super fast. So what to do with the problem at the printer? The relationship is because the thick ink will create a deadlock in the head and capping station on the printer.
What all white ink DTG white ink like that? Almost all the white ink as it had to be more concentrated than CMYK. If it is less dense then prints the shirts are based will not be solid white colour and will not
absorb to the t-shirt be a solid color.
Choosing a good DTG white ink
Consider carefully both the level of a concentration, the more intense it is, the better the results but not for the survival of head and capping station. Choose the level of a concentration was not too thick nor too thin. Note also the ink dry speed, the faster the dry increasingly also good for head and capping station. If that happens there will be a deadlock on the engine head DTG printer. And the last check is the expiration date of the product DTG white ink itself, getting closer to the expiration date of the ink will decrease. Ink will be more concentrated and dry quickly so your DTG printer machine will be more easily damaged.
Terimakasih anda telah membaca artikel tentang DTG Printer Problems, How To Solve ?. Jika ingin menduplikasi artikel ini diharapkan anda untuk mencantumkan link http://digital-preuneur.blogspot.com/2015/10/dtg-printer-problems-how-to-solve.html. Terimakasih atas perhatiannya.